Mobile Small Engine Mechanic in Angus and nearby(705) 500-9961

Mobile Carburetor Cleaning and Rebuild in Angus

Why your carb is probably the problem

Your engine cranks but won’t fire. Or it starts, runs rough for a minute, then dies. Sound familiar? Nine times out of ten, the carburetor is to blame. Old fuel gums up the tiny jets and passages inside, and once that happens the engine can’t get the right air-fuel mix.

This is especially common after equipment sits for a season. The ethanol in modern pump gas attracts moisture and leaves behind a sticky residue. A proper clean or rebuild gets things flowing again without replacing the whole engine.

What we actually do on the job

We disassemble the carb completely, soak and blow out every passage, and inspect the needle, seat, float, and gaskets. If anything is worn or cracked, we replace it. We also check the fuel line and filter while we’re in there, because there’s no point cleaning a carb and feeding dirty fuel back through it.

If the carb is too far gone - corrosion, stripped threads, broken castings - we’ll swap it for a new unit that fits your machine. We carry common replacement carbs and can source less common ones quickly. We’ll tell you upfront what makes sense for your equipment before we start.

We come to you - no trailering needed

We’re a mobile operation based in Angus. You don’t load anything into a truck or drop it at a shop. We show up at your driveway, garage, or property and do the work right there. We also serve Barrie, Innisfil, Alliston, Beeton, Cookstown, and surrounding areas across the Barrie region.

If you’re not sure whether we cover your address, just reach out. We serve a solid radius across Simcoe County and respond to quote requests promptly.

What equipment we work on

If it has a small engine and a carb, we can help. That includes lawn mowers, riding mowers, snow blowers, generators, pressure washers, chainsaws, trimmers, leaf blowers, and ATVs. Carb issues show up across all of them, usually for the same reason - stale fuel sitting too long.

If your mower needs more than a carb service, check out our Lawn Mower Repair and Small Engine Tune Up pages. Got a generator that won’t run? We handle that too - see Generator Repair Service. Storing equipment for the season? Our Seasonal Equipment Storage Prep service gets everything ready so you’re not dealing with a gummed-up carb next spring.

Signs it’s time to call us

Hard starting is the most obvious one. But also watch for surging (engine speed hunting up and down), black smoke from a rich mixture, or fuel leaking from the carb body. Any of those means something is off with fuel delivery.

Don’t ignore a small carb problem. A gunked-up carb puts extra strain on the rest of the engine. Catching it early is almost always cheaper than waiting until the machine won’t start at all before the first mow of spring or the first big snowfall.

Book your carb service today

Reach out through our contact form or give us a call. Tell us the make, model, and what it’s doing (or not doing), and we’ll give you a straight answer on what it likely needs. No shop drop-off, no waiting weeks for a bench spot.

We serve Angus, Essa, Tottenham, and everywhere in between. If you’ve also got a chainsaw or trimmer that needs attention, ask us about Chainsaw Repair Service and Leaf Blower Trimmer Repair - we can often tackle multiple machines in one visit.

FAQ — Carburetor Cleaning Rebuild

How do I know if my carburetor needs cleaning or a full rebuild?
Cleaning works when the carb is structurally sound but clogged with varnish or debris. A rebuild makes sense when the gaskets, needle, or seat are worn and causing fuel leaks or poor sealing. If the carb body itself is cracked or heavily corroded, replacement is usually the better call. We'll inspect it on the spot and tell you which option fits your situation.
Can you clean the carb on a machine that's been sitting for a few years?
Yes, and that's actually one of the most common jobs we do. Old fuel leaves behind a varnish that blocks the small passages inside the carb. A thorough soak and clean usually gets things running again. If the passages are too far gone or the float has absorbed fuel and sunk, we'll rebuild or replace what's needed.
Do I need to do anything to prepare my equipment before you arrive?
Not much. If you can, leave a bit of old fuel in the tank so we can observe how the engine behaves before we start work. Make sure there's reasonable access to the machine - a driveway or open garage spot is ideal. We bring our own tools and supplies, so you don't need to have anything on hand.

Other services we offer